|
|
High speed programmable digital pico servo with titanium gear and double BB-ed output shaft for small RC model planes, 1:16-1:24 RC cars, 400-450 size helicopters etc. Plastic case with middle aluminium heatsink for perfect cooling under high load.
GO-10S13MG is programmable using the KAVAN GO servo USB programmer/interface and PC software.
Programmable Functions
- Servo Angle: Maximal servo rotation angle range setting. The default range is ca 120° within the regular RC signal pulse width range (900~2100 µs); ca 180° within the max. signal pulse width range (500~2500 µs).
- Servo Neutral: Servo neutral (centre) position setting.
- Damping Factor: Servo damping setting – adjust the characteristics of the servo when stopping.
- PWM Power: Adjusts the servo output power. The higher the power, the higher the speed and torque of the servo – indeed also the current consumption will be higher.
- Sensitivity: Servo sensitivity (Dead Band) setting. The higher sensitivity the narrower the dead band – servo moves only if the change of the signal pulse width is bigger than the dead band width. Too high setting may cause servo jitter in some applications. Range: Ultra High (ca 1 µs dead band) – High (ca 2 µs) – Medium (ca 3 µs) – Low (ca 4 µs)
- Soft Start: Turns on/off the soft start feature. If ON, the servo goes slowly to the initial position corresponding to the servo signal once the power is switched on.
- Reverse: Reverses the servo movement direction.
- Narrow Band: FUTABA SR Mode – only for use with FUTABA radio channels working in the SR mode. Do not turn the option on if you are using a different setting of your FUTABA radio or any other radio.
- SANWA SSR: SANWA SSR Mode - only for use with SANWA radio channels working in the SSR mode. Do not turn the option on if you are using a different setting of your SANWA radio or any other radio.
- Lost PPM Protection (Fail-Safe): In the case the control signal from the receiver is lost completely or cannot be decoded correctly (due to interference) the servo can use choose one of three fail-safe modes:
- (a) Release: No fail-safe protection.
- (b) Keep Position: Keeps the position corresponding to the last correct control signal.
- (c) Go Neutral Position: The servo returns to the neutral (1500 µs pulse width) position.
- Over Load protection: Enables or disables overload protection of the servo in three levels – once the overload conditions last for the pre-set time (in seconds), the output power of the servo is reduced to the corresponding pre-set level (% of the max. power).
- Default: Restores the factory default setting of the connected servo.
Standard input voltage range 4.8-6.0 V (nominal).
25T/4.94 mm output shaft.
Servo dimensions | Micro |
Servo type | Digital |
Programmable | Yes |
Thrust at 4.8V [kg/cm] | 1.6 |
Thrust at 6.0V [kg/cm] | 2 |
Speed at 4.8V [s/60st.] | 0.09 |
Speed at 6.0V [s/60st.] | 0.08 |
Servo gears | Titanium |
Ball bearings | 2× |
High-voltage | No |
Power supply [V] | 4.8 - 6 |
Length [mm] | 22.8 |
Width [mm] | 12 |
Height [mm] | 29.4 |
Weight [g] | 15 |
Intended for | Aeroplanes,Helicopters,On-road cars,Off-road cars,Boats |
Equipments required
![]() | KAV20.0001 Name: GO servos USB programmer Price: 24,96€ ![]() Delivery status: contact us USB programmer/interface for programming KAVAN GO digital servos of the GO-10xx/11xx/12xx series with the help of a convenient PC operating program for Windows XP, Vista, 7, 8, 10 (32/64bit). |
Equipments required for models
![]() | KAV02.8027 Name: KAVAN Savage Mini - blue Price: 103,75€ ![]() Delivery status: in stock at supplier A builder’s kit of 3D aerobatic park-flyer (1000 mm wingspan) made of virtually unbreakable thoroughly carbon reinforced EPP foam for 200-300W brushless motors. Symmetrical wing section, SFG winglets and flat, large area fuselage for great 3D/knife edge handling. Aileron, elevator and rudder control. |